Standard Heated FID Emissions FID Analyzers

Low Cost Heated FID Analyzer 3-500

The J.U.M Heated Total Hydrocarbon Analyzer Model 3-500 FID is our lowest cost alternative to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons. The 3-500 is based on our time proven 300A FID platform of which we have sold thousands of analyzers.

The 3-500 fully complies with EN 12619, EN 13526 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It can be used as a table top instrument but is ideally suited to be integrated in CEMs.

• Made in Germany

• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house

• Fully heated to 190 degree C

• Typical sensitivity 0.01 ppm CH4

• Direct concentration (e.g. ppm) display allows to read up to 3 decade ranges without range change

• Internal sample pump and air pump

• Internal combustion air supply (No external air cylinder needed)

• Very low fuel consumption (less than 20 cc/min @ 100% H2)

• Disposable sample filter in rear panel

• Automatic ignite capability (optional)

• Automatic flame out alarm contact and fuel shut off

• Sample pressure regulator not in contact with sample gas

• Multiple range capability, 5 selectable ranges are standard

• 19" rack mount unit, only 132 mm high

• Stack gases (CEM) and all other Environmental and process applications

• Air and gas scrubber efficiency

• Process chemical gas analysis

• Personnel safety

• Solvent recovery

• Catalytic converter and thermal combustor testing

• Automotive and engine emissions

• Fence line (perimeter) monitoring

• Non-methane hydrocarbon measurements

Methane Only Option

The available Methane Only Option provides the capability to measure METHANE ONLY or TOTAL HYDROCARBONS. The choice is switch selectable from the front panel or by remote contact closure.

Heated FID Analyzer 3-600

The J.U.M Heated Total Hydrocarbon Analyzer Model 3-600 FID is another low cost alternative to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons. The 3-500 is built on our time proven 300A FID platform of which we have sold thousands of analyzers.

The 3-600 fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It can be used as a table top instrument but is ideally suited to be integrated in CEMs.

Features

• Made in Germany

• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house

• Fully heated to 190 degree C

• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional

• Typical sensitivity 0.01 ppm CH4

• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change

• Internal sample pump and air pump

• Internal combustion air supply (No external air cylinder needed)

• Very low fuel consumption (less than 20 cc/min @ 100% H2)

• Disposable sample filter in rear panel

• Automatic ignite capability (optional)

• Automatic flame out alarm contact and fuel shut off

• Sample pressure regulator not in contact with sample gas

• Multiple range capability, 5 selectable ranges are standard

• 19" rack mount unit, only 132 mm high

• Stack gases (CEM) and all other Environmental and process applications

• Air and gas scrubber efficiency

• Process chemical gas analysis

• Personnel safety

• Solvent recovery

• Catalytic converter and thermal combustor testing

• Automotive and engine emissions

• Fence line (perimeter) monitoring

• Non-methane hydrocarbon measurements

Methane Only Option:

The available Methane Only Option provides the capability to measure METHANE ONLY or TOTAL HYDROCARBONS. The choice is switch selectable from the front panel or by remote contact closure.

Heated FID Analyzer for FTIR based CEM's, 3-700

The J.U.M Heated Total Hydrocarbon Analyzer Model 3-700 FID is designed to be installed directly upstream of a FTIR analyzer (e.g. Gasmet) to continuously measure the total concentration of hydrocarbons within a gaseous sample. All controls which allow to calibrate the FTIR or FID individually are built in. Sources can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons.

The 3-700 fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It can be used as a table top instrument but is ideally suited to be integrated in CEMs.

Features

• Made in Germany

• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house

• Fully heated to 190 degree C

• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional

• Typical sensitivity 0.01 ppm CH4

• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change

• Internal sample pump and air pump

• Internal combustion air supply (No external air cylinder needed)

• Very low fuel consumption (less than 20 cc/min @ 100% H2)

• Disposable sample filter in rear panel

• Automatic ignite capability (optional)

• Automatic flame out alarm contact and fuel shut off

• Sample pressure regulator not in contact with sample gas

• Multiple range capability, 5 selectable ranges are standard

• 19" rack mount unit, only 132 mm high

• Stack gases (CEM) and all other Environmental and process applications

• Air and gas scrubber efficiency

• Process chemical gas analysis

• Personnel safety

• Solvent recovery

• Catalytic converter and thermal combustor testing

• Automotive and engine emissions

• Fence line (perimeter) monitoring

Transportable Heated FID 3-800

The J.U.M 3-800 Portable Heated Total Hydrocarbon Analyzer is a heavy duty FID analyzer to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons.

The 3-800 fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It is ideally suited to be used in all stack emissions applications.

Features

• Made in Germany

• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house

• Fully heated to 190 degree C

• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional

• Typical sensitivity 0.01 ppm CH4

• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change

• Internal sample pump and air pump

• Optional 50 liter metal hydrid low pressure fuel storage cartridge, good for 50 hours of uninterrupted measurements

• Very low fuel consumption (less than 20 cc/min @ 100% H2)

• Internal combustion air supply (No external air cylinder needed)

• Disposable sample filter in rear panel

• Automatic ignite capability (optional)

• Automatic flame out alarm contact and fuel shut off

• Sample pressure regulator not in contact with sample gas

• Multiple range capability, 5 selectable ranges are standard

Applications

• Stack gas emissions and all other Environmental and process applications

• Air and gas scrubber efficiency

• Process chemical gas analysis

• Personnel safety

• Solvent recovery

• Catalytic converter and thermal combustor testing

• Automotive and engine emissions

• Fence line (perimeter) monitoring

Transportable Heated FID THC / Methane FID Analyzer 3-900

The J.U.M 3-900 Portable Heated Methane Only and Total Hydrocarbon Analyzer is a heavy duty FID analyzer to continuously measure methane only or the total hydrocarbons to determine the non methane hydrocarbon concentration within a gaseous sample . This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons.

The 3-900 fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It is ideally suited to be used in all stack emissions applications.

Features

• Made in Germany

• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house

• Fully heated to 190 degree C

• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional

• Typical sensitivity 0.01 ppm CH4

• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change

• Internal sample pump and air pump

• Optional 50 liter metal hydrid low pressure fuel storage cartridge, good for 50 hours of uninterrupted measurements

• Very low fuel consumption (less than 20 cc/min @ 100% H2)

• Internal combustion air supply (No external air cylinder needed)

• Disposable sample filter in rear panel

• Automatic ignite capability (optional)

• Automatic flame out alarm contact and fuel shut off

• Sample pressure regulator not in contact with sample gas

• Multiple range capability, 5 selectable ranges are standard

Applications

• Stack gas emissions and all other Environmental and process applications

• Air and gas scrubber efficiency

• Process chemical gas analysis

• Personnel safety

• Solvent recovery

• Catalytic converter and thermal combustor testing

• Automotive and engine emissions

• Fence line (perimeter) monitoring

Light Weight Portable Heated FID THC Analyzer OVF-3000

The J.U.M OVF-3000 Portable Heated Total Hydrocarbon Analyzer is a light weight, over the shoulder portable heated FID analyzer to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons. The standard OVF-3000 is equipped with our new low pressure metal hydrid fuel storage system which is good for continuous operation for 50 hours. Fuel Storage can be safely refilled by the user.

It fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It is ideally suited to be used in all stack emissions applications.

Features

• Light weight, internal fuel storage, easy to operate

• Made in Germany

• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house

• Fully heated to 180 degree C

• Typical sensitivity 0.01 ppm CH4

• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change

• Internal sample pump and air pump

• Optional 50 liter metal hydrid low pressure fuel storage cartridge, good for 50 hours of uninterrupted measurements

• Very low fuel consumption (less than 20 cc/min @ 100% H2)

• Internal combustion air supply (No external air cylinder needed)

• Disposable sample filter in front panel

• Automatic flame out alarm contact and fuel shut off

• Sample pressure regulator not in contact with sample gas

• Multiple range capability, 5 selectable ranges are standard

Applications

• Stack gas emissions and all other Environmental and process applications

• Air and gas scrubber efficiency

• Process chemical gas analysis

• Personnel safety

• Solvent recovery

• Catalytic converter and thermal combustor testing

• Automotive and engine emissions

• Fence line (perimeter) monitoring

Heated Non Methane/ Methane/ Total Hydrocarbon FID Analyzer 109L

The J.U.M 109L is a heated FID analyzer to continuously and simultaneously measure the Methane concentration, the Total Hydrocarbon concentration and the Non Methane concentration within a gaseous sample. The 109L is a table top or 19 inch rack mount Heated FID analyzer for the NMHC measurement in ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons.

The 109L can be used as a table top or rack mount analyzer. It fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA).

Features

• Made in Germany

• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house

• Dual detector/ dual electrometer design

• Fully heated to 190 degree C

• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional

• Typical sensitivity 0.01 ppm CH4

• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change

• Internal sample pump and air pump

• Internal combustion air supply (No external air cylinder needed)

• Very low fuel consumption (less than 20 cc/min @ 100% H2)

• Disposable sample filter in rear panel

• Automatic ignite capability (optional)

• Automatic flame out alarm contact and fuel shut off

• Sample pressure regulator not in contact with sample gas

• Multiple range capability, 5 selectable ranges are standard

• 19" rack mount unit, 221 mm high

Applications

• Optimization of natural gas fired baking ovens and other furnaces

• Gas purifying system monitoring

• Stack gases (CEM) and all other Environmental and process applications

• Air and gas scrubber efficiency

• Process chemical gas analysis

• Personnel safety

• Solvent recovery

• Catalytic converter and thermal combustor testing

• Automotive catalyst and engine emissions

• Fence line (perimeter) monitoring

Wall or Panel Mount Heated FID THC Analyzer W600

The J.U.M W600 Heated Total Hydrocarbon Analyzer is a very compact wall or panel mount heated FID analyzer to continuously measure the total concentration of hydrocarbons within a gaseous sample. This can be ambient air, exhaust gases from a combustion process e.g. stack emissions, from any type of an industrial vent, from an internal combustion engine, or from any other emission containing hydrocarbons.

The W600 can easily be wall or panel mounted or can be integrated into a NEMA type enclosure, for example to meet area classifications. It also can be mounted directly on a duct or stack wall. It fully complies with EN 12619, EN 13526, QAL 1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). It is ideally suited to be used in all stack emissions applications.

Features

• Made in Germany

• All critical components including pumps, sample filters, detectors and main electronics are manufactured in house

• Fully heated to 190 °C

• Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional

• Typical sensitivity 0.01 ppm CH4

• 21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change

• Internal sample pump and air pump

• Internal combustion air supply (No external air cylinder needed)

• Very low fuel consumption (less than 20 cc/min @ 100% H2)

• Disposable sample filter in rear panel

• Automatic ignite capability (optional)

• Automatic flame out alarm contact and fuel shut off

• Sample pressure regulator not in contact with sample gas

• Multiple range capability, 5 selectable ranges are standard

• 19" rack mount unit, only 132 mm high

Applications

• Bio gas purifying system monitoring

• Stack gases (CEM) and all other Environmental and process applications

• Air and gas scrubber efficiency

• Process chemical gas analysis

• Personnel safety

• Solvent recovery

• Catalytic converter and thermal combustor testing

• Automotive and engine emissions

• Fence line (perimeter) monitoring.